- Product Details
- {{item.text}}
Quick Details
-
Place of Origin:
-
Zhejiang, China
-
Brand Name:
-
Volcano Electric
-
Model Number:
-
VOL-PM500A12
-
Torque:
-
3.18Nm
-
Housing:
-
Aluminum Frame
-
Speed Range:
-
1500rpm
-
Material:
-
Permanent Magnets
-
Controller:
-
Customized, Optional
-
Braker:
-
Optional
-
Insulation Class:
-
Class F
-
Enclosure:
-
IP54
-
Poles:
-
4P, 6P, 8P...
-
Wire:
-
100% copper
-
Buty:
-
S1 (continuous)
Quick Details
-
Speed(RPM):
-
1500RPM
-
Continuous Current(A):
-
45.29A
-
Efficiency:
-
IE 2
-
Place of Origin:
-
Zhejiang, China
-
Brand Name:
-
Volcano Electric
-
Model Number:
-
VOL-PM500A12
-
Torque:
-
3.18Nm
-
Housing:
-
Aluminum Frame
-
Speed Range:
-
1500rpm
-
Material:
-
Permanent Magnets
-
Controller:
-
Customized, Optional
-
Braker:
-
Optional
-
Insulation Class:
-
Class F
-
Enclosure:
-
IP54
-
Poles:
-
4P, 6P, 8P...
-
Wire:
-
100% copper
-
Buty:
-
S1 (continuous)
| Motor type | Output Power | Voltage | Load | Speed | Rated Torque | Efficiency | Noise | IP Class |
| KW | V | A | RPM | Nm | % | dB | ||
| VOL-BL3K5A72 | 3.5 | 72 | 51.71 | 1500 | 22.28 | 94 | 62 | IP 54 |
| VOL-BL3K5A110 | 3.5 | 110 ac | 19.54 | 1500 | 22.28 | 94 | 62 | IP 54 |
| VOL-BL3K5A220 | 3.5 | 220 ac | 9.77 | 1500 | 22.28 | 94 | 62 | IP 54 |
| VOL-BL3K5A380 | 3.5 | 380 ac | 5.66 | 1500 | 22.28 | 94 | 62 | IP 54 |
| VOL-BL3K5B72 | 3.5 | 72 | 51.71 | 3000 | 11.14 | 94 | 62 | IP 54 |
| VOL-BL3K5B110 | 3.5 | 110 ac | 19.54 | 3000 | 11.14 | 94 | 62 | IP 54 |
| VOL-BL3K5B220 | 3.5 | 220 ac | 9.77 | 3000 | 11.14 | 94 | 62 | IP 54 |
| VOL-BL3K5B380 | 3.5 | 380 ac | 5.66 | 3000 | 11.14 | 94 | 62 | IP 54 |
Q:
Motor has been running then fails to start,what to do?
A:
Likely cause: Fuse or circuit breaker is tripped.
What to do: Replace the fuse or reset the breaker.
Likely cause: Armature is shorted. Motor may make a humming noise and the circuit breaker or fuse will trip.
What to do: Disassemble motor and inspect the armature for a burnt coil. Inspect the commutator for burnt bars. If this condition exists, the motor needs to be replaced.
Likely cause: The brushes may be worn down too far and no longer make contact with the commutator.
What to do: Check the brushes to make sure that they are still making contact with the commutator. Contact manufacturer for brushes.
Likely cause: Controller may be defective.
What to do: Verify voltage is coming out of the controller.
Q:
On initial installation, motor fails to start up,what to do?
A:
Likely cause: Motor is incorrectly wired
What to do: Verify that the motor is wired correctly.
Likely cause: No output power from controller.
What to do: Measure voltage coming from the controller.
Likely cause: Motor is damaged and the armature is rubbing against the magnets.
What to do: Disassemble motor and see if the armature can be realigned by reassembly. Motor may have to be replaced.
Q:
Motor takes too long to accelerate,what to do?
A:
Likely cause: Motor controller not properly set.
What to do: Adjust the acceleration trim pot of the controller.
Likely cause: Brushes are worn.
What to do: Verify brush length.
Likely cause: Bearings may be defective.
What to do: Inspect bearings. Noisy or rough bearings should be replaced.
Q:
Motor runs in the wrong direction,what to do?
A:
Likely cause: Incorrect wiring
What to do: Interchange the two motor leads.
Q:
Motor runs OK but has a clicking noise,what to do?
A:
Likely cause: Suspect a burr on the commutator.
What to do: Remove burr from commutator using a commutator stone.
