CV40 Carburetor Universal for Harley Davidson HD Sportster Softail Touring Dyna & FXR Road King Evo Twin Cam Motorcycle Carb

CV40 Carburetor Universal for Harley Davidson HD Sportster Softail Touring Dyna & FXR Road King Evo Twin Cam Motorcycle Carb

FOB Reference Price: Get Latest Price

≥1 Pieces

US $53.31

≥20 Pieces

US $51.31

≥200 Pieces

US $49.31

≥1000 Pieces

US $47.31

Free Inquiry

Customized Request

Product Details

{{item.text}}

Quick Details

Product Type:: Carburetor

Applicable Brand:: Harley Davidson

Part Number:: 27421-99 27490-04 27465-04

Material:: Aluminum alloy

Package Size:: 17*12.5*12.5 cm

Package Size(box):: 62*36*27 cm

Weight:: 1.02 kg

Weight(box):: 20.4 kg

Packing:: Carton Packing

Delivery Terms:: EXW,FOB,CFR,CIF,DDU

Quick Details

Place of Origin:: Fujian, China

Brand Name:: Rui Jie

Warranty:: 1 year guarantee

Product Type:: Carburetor

Applicable Brand:: Harley Davidson

Part Number:: 27421-99 27490-04 27465-04

Material:: Aluminum alloy

Package Size:: 17*12.5*12.5 cm

Package Size(box):: 62*36*27 cm

Weight:: 1.02 kg

Weight(box):: 20.4 kg

Packing:: Carton Packing

Delivery Terms:: EXW,FOB,CFR,CIF,DDU

Products Description

CV 40 carburetor is mainly suitable for the following models of motorcycles

Most of them are Harley Davidson series motorcycle

Year	Fit brand	Model
1989-2007	Heritage Softail
1989-1992	Low Rider
1988-2017	Softail
1988-2016	Dyna & FXR
1988-2016	Touring
1998-Up	Sportster	883 / 1200
1999-2007	Night Train
1990-2007	Fatboy
1989-2007	Electra Glide

CV Carburetor Modifications For EVO and Twin Cam engines

Step 1. REMOVE THE CARBURETOR

Remove the carburetor as described the service manual for your model bike. You might get away with leaving the throttle cables connected. It is much easier to remove the carburetor and use a work bench. Leave the choke cable hooked to the carburetor and disconnect the pull-handle end, taking the entire choke cable/carburetor assembly with the carburetor. It is faster to cut the fuel line hose off rather than trying to save it.

Tricks of the trade

If you take out the rear fuel tank bolts and loosen the front bolts, the fuel tank can be raised a few inches. The extra room gained by raising the tank is the difference between struggling with the job and making it easy.

Step 2: MODIFY THE IDLE MIXTURE ADJUSTMENT

The aluminum plug covering the idle mixture adjusting screw needs to be removed. Turn the carburetor over and locate the plug toward the rear of the carburetor, in back of the float bowl. Using about a 1/16" drill bit, carefully drill a hole through the small plug (CV Carburetor Cutaway item #9). If the plug does not fall out while drilling, remove the drill bit. Carefully insert a small self-tapping sheet metal screw into the plug. This will allow enough grip to remove the plug by pulling on the self-tapping screw with a pair of pliers.

Underneath you will find a slotted screw. Turn this screw clockwise until it is GENTLY seated. Over tightening this screw can damage the carburetor and needle. Back the idle mixture screw 2 1/2 full turns. This provides a starting point for tuning.

Step 3: SLIDE MODIFICATIONS

Remove the top of the carburetor (slide vacuum chamber cover) being careful to loosen the throttle linkage stop plate. There is a spring under the top cover, so hold it with a finger until all screws are loose. Holding the carburetor upright, remove the cover and spring. The slide/diaphragm assembly can now be removed. Inside the slide you will see the plastic spring seat. Under the spring seat is the jet needle. These two items can be removed by turning the slide over and pouring the parts into you hand. These parts are needed for reassembly of the carburetor.

On the bottom of the slide are two holes. The center hole is for the jet needle. The second hole is off center. This is the vacuum port (CV Carburetor Cutaway #4). This hole needs to be drilled to 1/8". Make sure this hole is a clean straight hole. Keep the shavings away from the rest of the carburetor. Remove any burrs that exist and clean the slide. Set the slide aside for now.

Step 4: REPLACE JETS

Turn the carburetor over so the bottom is facing upward. Remove the float bowl by removing the four screws. Carefully remove the fuel bowl. Using a flat blade screwdriver, replace the stock #42 slow jet with a #45 jet (CV Carburetor Cutaway 8). If you use the OEM needle, the main jet will be replaced with a jet 10 larger than the OEM. If you use the XL needle, the main jet will be replaced with a 165 jet(CV Carburetor Cutaway 7). The jets are brass parts that are screwed into an aluminum body. Do not over-tighten the new jets when installing them. Replace the float bowl, carefully placing the accelerator pump rod into its rubber boot.

Step 5: RE-ASSEMBLE THE CARBURETOR

If you use the OEM needle, place 1 (approx. .050" or 1/16" thick) of the small brass washers over the long end of the needle jet (Slide Detail 3). These washers will raise the jet needle taper, richening the low RPM fuel mixture. Place the jet needle into the slide, making sure the washers remain in place. If you did not get thin brass washers, a single small washer of up to 1/8" thick can be used. Make sure the washer is the smallest that can be found.

If you are using the XLH needle, place the jet needle into the slide without using any washers. Replace the spring seat into the slide and over the jet needle. Place the carburetor slide into the carburetor body. Carefully place the edges of the diaphragm into the grove around the top of the carburetor. Install the slide spring and the carburetor top being careful not to mis-align or pinch the diaphragm.

Assembly Tricks for the diaphragm

The diaphragm is easily mis-aligned or pinched. This is a common source of problems after carburetor modifications are performed. The diaphragm frequently has the appearance of being too large to fit into the groove. The repeated up and down movement of the diaphragm causes it to stretch, making re-assembly tricky. Try using the cap to position the diaphragm. It will allow you to evenly push the diaphragm into the groove. You can "wiggle" the top and feel when the diaphragm is properly located. A damaged diaphragm will have the symptoms of the engine being able to idle, but will not accept any throttle. If you think the diaphragm is damaged, check for any pinholes with a bright light behind the rubber, pulling on the edges to stretch the diaphragm a bit. If you find any, the entire slide/diaphragm assembly must be replaced.

Step 6: PUT THE CARBURETOR BACK ON THE BIKE

The carburetor is now ready to be installed back on the engine. Place the fuel line on the carburetor before you place it on the bike. Replace the carburetor, directing the fuel line and choke cable into position as you move the carburetor into place. Remember to replace the vacuum hose from the VOES to the top rear of the carburetor. Checking all the work to make sure screws and hoses are properly installed. Be careful not to over-tighten the choke cable mounting nut as the plastic will break fairly easily. Lower the fuel tank back into place. Connect the fuel line hose to the fuel petcock. If you have a late model bike with the vacuum line connected to the fuel petcock, make sure the hose is connected.

Step 7: WARMING UP THE BIKE

Warm the bike up to full operating temperature. Prior to final adjustments the engine may not idle properly. The carburetor is not as lean as the factory settings. DO NOT follow the owner's manual directions for cold starting. he new procedure is as follows: If the engine is cold, pull choke out all the way. If the engine is warm, use half or no choke at all. Start the bike, adjusting choke to reduce the fast idle to a reasonable speed. About 30 seconds later, push the choke all the way in and use the throttle to keep the bike idling while warming up. The throttle lock can be used for this purpose during initial adjustments. Letting the bike idle for 15 minutes to warm up is not desirable. The modifications made to your bike should allow it to run well enough for a sedate test run around the block. This speeds up the warm-up time and also allows a feel for the improvement to throttle response from the modifications. As the bike comes up to proper operating temperature, adjustments to the idle mixture and idle speed can be performed.

Tricks of the trade

A small, flat blade screwdriver about 3" long should be used to adjust the idle mixture screw. Fumbling around with the wrong screwdriver usually results in burned knuckles. Make sure the screwdriver works before the engine is started. To adjust the idle speed, a long, flat blade or #1 Phillips screw driver should be used. This allows the screwdriver to get past the various obstructions that exist between you and the idle mixture screw.

Step 8: ADJUSTING IDLE MIXTURE

The CCP idle mixture screw allows fine tuning without a screwdriver. Click For Info. With engine warmed up and at idle, turn the idle mixture screw inward (clockwise) slowly until the engine starts to stumble. If the engine will not idle on its own during this procedure, raise the idle by adjusting the idle set screw until it does. Make a mental note of the position of the clock position of the screwdriver. Now turn the idle mixture screw outwards until the engine begins to run smoothly, adjusting the idle stop screw as necessary to maintain proper idle speed. Blip the throttle a time or two and observe the results. If the engine responds quickly with a gratifying blast and no backfiring through the carburetor, you have your idle mixture right. If backfiring occurs through the carburetor then adjust the idle mixture screw out another 1/8 to 1/4 turn. Under normal circumstances, the idle mixture screw should be between 2 and 3 turns out. Adjusting the idle mixture screw out to far results in an overly rich, low RPM fuel mixture leading to poor gas mileage and carbon buildup in the combustion chamber. Big Twin Idle Speed The proper idle speed for Big Twin engines is 900-1000 RPMs. EVO oiling systems need better than 700 RPM to work properly. Resist the temptation to lower the idle excessively. It may sound good, but improper oiling will contribute to engine overheating while idling in traffic and premature engine failures.

Step 9: FINE TUNING

The details of carburetor tweaking and plug reading is a very involved subject, so you may want to refer to a higher authority after this. If you do not have access to a Dyno facility, here is a very basic guide that will get the adjustments close. To test the main jetting, you must be in fourth or fifth gear and running fairly high RPM (4000+) then open the throttle all the way to the throttle stop, noting the feel of the bike. Immediately let off the throttle about 1/8 turn and note the feel of the bike. If it seems to accelerate some when you let off the 1/8, your main jet is too lean. If it hesitates or the top speed is poor (i.e. less than 80 MPH) you are too rich. Adjust your main jetting accordingly by increasing or decreasing the jet size by 5. Use your common sense and seat of the pants feel and you will get close enough to do plug reads. Plug reading is as much an art as a science, taking years of experience to understand what the plugs are really telling us about the engine. For most street riders, making sure the plugs are a nice light tan color is good enough. Don't read the plugs until the fine tuning has been done and then make sure you use new plugs. Do some riding which exercises either low speed or main jetting, then stop immediately shutting down the engine before it is at idle speed. Checking the plugs this way will provide the most accurate reading. If your plugs are black you are too rich, which decreases your gas and performance but will not harm your engine. Too light or worse yet bone white you are too lean, and engine damage will soon follow if proper steps are not taken richen the mixture.

Main Products