T-4000 LED SD card led pixel controller;can max control 4096 pixels;supports WS2811/WS2812B/LPD8806/SK6812/1903/TM1804.etc

1. T-4000 System characteristics

1. 32—256 Gray level, Support software Gamma correction

2. Support the rules and special-shaped handle.

3. Four-port output, every port can support 512-1024 pixels

4. Off-line(SD Card) control, play back content stored in the SD card.

5. The controller Can save up to 16 files ,copy the file into SD card in order.

6. The file in SD card must be named: 00_1.led, 01_1.led, 02_1.led…….

7. Compatible with single and dual IC, if you control a single line IC LED lights, without being connected to the CLK line.

2.Support chips

Chip type	Software code& Controller type	Lamps/(MAX)	Note
LPD6803,D705,1101,6909, 6912	T-4000-6803	4096
LPD8806,LPD8809	T-4000-8806	4096
TM1803,TM1804,TM1809,TM1812	T-4000-TM	4096	TM1804 and TM1809 are divided into high speed and low speed
TM1903, TM1904, TM1909, TM1912	T-4000-TM19	4096
UCS6909,UCS6912,UCS7009,UCS5903	T-4000-UCS-32	4096
UCS1903,UCS1909,UCS1912	T-4000-UCS-256	4096	divided into high speed and low speed
UCS3903	T-4000-UCS-1024	4096
DMX512	T-4000-DMX	680/2048	Compatible with standard DMX512
WS2801,WS2803	T-4000-WS	4096
WS2811	T-4000-WS2811	4096	divided into high speed and low speed
DS189	T-4000-DS189	4096
TLS3001,TLS3002,TLS3008	T-4000-TLS	——
P9813	T-4000-P9813	4096
SM16715	T-4000-SM16715	4096	divided into high speed and low speed
SM16716	T-4000-SM16716	4096
BS0901,BS0902	T-4000-0901	4096
BS0815	T-4000-0815	4096

The meaning of flag

Button	Meaning
SET	Save your adjust
MODE	Switch effect file
SPEED+	Turn up speed	Press the speed adjustment button the file will in turn play.
SPEED-	Turn down

DC5V	Power input
POWER	Power light
ERROR	Error indicator
SD CARD	SD card slot

CLK	Clock line
DAT	Data line
GND	Ground wire

NOTE: For the TTL(SPI) signal, the controller signal ground must connect to the LED ground wire directly.

T-4000 can only used independently

6. File saving

Rules for naming files

“ 00.led” ---------the first effect file

“ 01.led” --------- the second effect file

“ 02.led” --------- the third effect file

“ 03.led” --------- the fourth effect file

Specific parameters:

Memory card:

type: SD card (suggest using high-speed SD card)

Capacity: 128MB—2GB

Format: FAT

Store file Format: *.led

Physical parameters:

Working temperature :-30—85

Working voltage: DC5V

Working power: 3W

Size: L170mm×W91mm×H31mm

Signal port: 3pin connect port

Weight: 0.36KG

NOTE:

Before copy files to SD card , The SD card must be formatted as FAT format.

The SD card in controller can not be hot-swappable, plug the SD card every time, you must first disconnect the power supply

8. Trouble shooting:

Question 1: After power, the T-4000 ERROR indicator has been flashing without display output

answer: The ERROR indicator has been flashing means the controller did not read the card correctly, possible problems:

1. SD card is empty, with no effect file.

2. The effect file in the SD card and the controller model are not match, please choose correct controller model in LedEdit and then re-create the effect file *led.

3. SD card did not format to FAT before copy effect files.

4. Please check the supply power voltage, the controller can be individually powered to exclude power reasons

5. Changing the SD card and then test to exclude the possibility of a bad SD card

Question 2: The controller is powered on, the indicator is normal, but the lamps have no effect change

Answer: The reasons for this are as follows:

1. Check if the lamp′s signal line and the controller connected correctly

2. If the TTL signal is received, the lamp and the controller must be common ground, that means connect the lamp′s and the controller′s ground together

3. Check if the model chose during making display files on the SD card match the chips used in the lighting

Question 3: Controller and light connected, after. Lamps flicker. Controller  indicator to normal.

Answer

1. The ground wire is not connected between the controller and lighting.

2. The file in SD card is bad, Chip model does not match with the actual.

3. Insufficient power supply.

Question 4: The SD card can not be formatted.

Answer

1. First make sure the SD card on the side of the protection switch is already open.

2. SD card reader is broken

3. Do all of this can’t deal with the question. Change the SD card tests again.

Memory Card:
. Type: SD Card (included)
. Support Capacity: 128MB-2GB
. File Format: FAT file format
. Store files: *.led
Physical parameters:
. Weight:0.5kg
. Temperature :-40-85 Degree
. Volgate: 110-240V AC
. Power:3W

Features:

1. 256 Gray,Gamma correction processing software.
2. Support the rules and special-shaped handle.
3. Controller, 4 ports output, may support 4096 pixel lights.
4. Off-line control, play back content stored in the SD card
5. T-4000 store a maximum of 16 documents