Motorcycle Ignition Start Switch/Fuel Tank Cap/ Electric door lock for CFMOTO CF150NK

♥Made of high quality material and advance technology.

♥Strong environment adaptation,high reliability.

♥Good performance and long service life.

♥Water resistance to interference.

♥We may offer you many kinds of switches, such as ignition switch, fuel tank cap, key sets, head lock, side lock, etc.

【Step 1: Prepare Engine for Installing New Ignition Coil】

Turn off the engine ignition switch and disconnect the ground cable for the battery. Remove the fuel tank to access the ignition coil and spark plugs. Remove the motorcycle seat as well if needed.

【Step 2: Disconnect the Ignition Coil】

At the ignition coil, disconnect 2 wires: the cable going to the ignition switch, and the black ground cable. Take off the ignition cover plates and the gasket. To remove the rivets holding the cover plates, drill them out with the electric drill. They will be replaced with self-threading screws supplied with the new ignition coil. Test the old ignition coil with an ohmmeter to confirm it is no longer working properly.

【Step 3: Set Out the Parts You Need in Order from Front to Rear】

Some motorcycles have multiple ignition coils, perhaps one per cylinder. Change the coils in order from the front to the rear of the engine to avoid confusing them. Mark the spark plug wires that connect to each coil in order to make installing the new ones easier.

【Step 4: Modify Connectors as Needed】

Some ignition coils need a right-angled wire connector so the wires fit correctly. Slip the right-angled boot onto the wire and push it up the wire. Flatten the ignition wire with cutting pliers and needle nose pliers and open up the original copper connector and trim it to fit the reverse side of the right-angled connector.

【 Step 5: Connect the Wire to the New Connector】

Using crimp pliers or needle nose pliers, fold and crimp the connector onto the ignition coil wire. Make sure the small "ear" sections of the connector are embedded into the ignition coil wire. You can also solder the connector into the right-angled connector. Test the connections between the ignition wire and connectors at both ends with an ohmmeter. If one coil has failed, its reading will be zero ("open") on the ohmmeter.

【Step 6: Cover Connectors with Right-Angled Boots】

Slide the right-angled boots down the wire so they cover the right-angle connectors. Turn the boot covers so there is adequate clearance between the ignition coil wires and the engine.

【Step 7: Reattach the Ignition Coil Covers】

If these are metal covers, use the self-threading screws with locking nuts to reattach the covers. If the covers are plastic, they will just slip over the coils and snap on.

【Step 8: Reinstall the Fuel Tank】 Mount the fuel tank over the engine and secure it with the mounting bolts. Fasten the fuel line into place.

【Step 9: Reinstall the Motorcycle Seat】 Put the seat back onto the frame and hook the seat into it. Ensure the seat is securely fastened.

Go Kart Parts ATV/UTV Parts Scooter Parts Golf Cart Parts

Motorcycle  Parts Bicycle Parts MINIBike Parts Customized Parts

Taizhou Xinydd Machinery Co., Ltd. was founded in 2015. We located in Binhai Industrial Area, Taizhou, Zhejiang Province. We have professional engineers and management team in the producing of the clutches for U.S.A, Russian, Europe, Brazil, and other countries. We have enough ability to satisfy different requirements from yours in this field.Who could bring a lot of international experience and professional and an unparalleled level of service for you.

Q1. How to pay?
A: TT, PAYPAL, WEST UNION, DP, DA, Credit card up to you.

Q2. What is your term of delivery?
A: EXW, FOB, CFR, CIF, DDU.

Q3. How about your delivery time?
A: Generally, it will take 24-48 hours after receiving your advance payment. Some is one week. The specific delivery time depends on the items and the quantity of your order.

Q4. How to produce customized products?
A: Yes, we can produce by your samples or technical drawings. We can build the molds and fixtures.

Q5. How to get a sample?
A: We can supply the sample if we have ready parts in stock.

Q6. Do you test all your goods before delivery?
A: Yes, we have 100% test before delivery.

Q7: How do you make our business long-term and good relationship?
A: 1. We keep good quality and competitive price to ensure our customers benefit ;
2. We respect every customer as our friend and we sincerely do business and make friends with them, no matter                 where they come from.