Aquaseal Table Top Marine Crystal Clear Super Gloss arts and crafts Epoxy 1:1 Resin in Clear 1 Gallon Kit Epoxy Wood Resin

1.Weigh A and B glue according to the given weight ratio into the prepared cleaned container, fully mixed the mixture again the container wall by clockwise, place it along for 3 to 5 minutes, and then it can be used.

2.Take the glue according to the usable time and dosage of mixture to avoid wasting. When the temperature is below 15 ℃, please heat A glue to 30 ℃ first and then mix it to the B glue (A glue will be thicken in low temperature ); The glue must be sealed lid after use to avoid rejection caused by moisture absorption.

3.When the relative humidity is higher than 85%, the surface of the cured mixture will absorb moisture in the air, and form a layer of white mist in the surface, so when the relative humidity is higher than 85%, is not suitable for room temperature curing, suggest to use the heat curing.

1,The operating environment should be ventilate and should keep away from fire. Closely sealed after use.
2, Avoid eye contact, in case of contact, wash with plenty of water and get medical attention immediately.

3, If contact skin, wrap with clean cloth or paper, and wash it with water and soap.
4, Keep away from children.
5, Please take a trial before application to avoid usage mistake.

1.JINHUA clear and transparent epoxy resin AB glue made from basic pure resin and do well in adhesive.

2.Good at UV and yellow resistance,self leveling,without bubble,high brightness.

3.Can be cured at nomal temperature or by heating.

4.Clear,low viscosity,nature defoaming, super transprency and good performance after mixed.

5.Can get any color you want by add pigments.

6.Easy to clean and repair.

7.No ripple,bright in surface,odourless,eco-friendly,nontoxic,waterproof and so on.

Clear Epoxy Resin 100% made in china Please Note: This kit is 1 gallon total. The resin weighs 4.10lbs. pounds and the hardener weighs 3.15 pounds. This product cures very hard and exhibits good air release. Excellent chemical and water resistance. Finished product cures clear with a super high gloss finish. Easy to use at a 1:1 mix ratio (By Volume) (Example 1 cup to 1 cup) Curing This product provides fast cure and property development at ambient and low temperatures without accelerators and allows for quick return to service. Typical pot-life on this item is roughly 45-50 minutes based on mass and temperature. Thin film set time (3mil. film) is roughly 5 hours at 78F. Fast cure and green time while exhibiting low exothermic temperatures (120C.) makes this product ideal for all applications. Full cure is 24 hours at normal conditions. This product cures to a brilliant high gloss finish. The finished product will be very rigid, smooth, clear, and display a brilliant high gloss finish similar to glass. Mixing, Storage, and Application Mix this resin 1:1 by volume. If mixing by weight, mix 100 parts of resin into 83 parts of hardener. When mixing this product, make sure to use a round cup & mix thoroughly scraping all sides and bottom of mixing container. Improperly mixed epoxy can create a major headache. Remember that thermoset plastics are temperature sensitive. Cold weather slows the cure process down, whereas heat speeds curing up. Always try to mix chemicals at room temperature. For best results, try pouring epoxy into hardener. Pour along the side of the container to help alleviate air entrapment. Mix for at least 3-5 minutes in a in a round motion until chemical are clear and free of striations. Allow the mixed components to stand in your mixed cup for at least 5 minutes. This allows for bubbles to rise to the surface. Small castings and potting units may take longer to cure than larger items. This chemical needs to be stored in a dry, safe, temperature controlled environment. Always keep the lids tightly sealed when not in use. Remember, oxygen and moisture oxidize and can rapidly degrade the epoxy and hardener. Moisture is also a potential issue. Always keep the bottles sealed when not in use. When applying this product, use gloves, goggles, and proper safety equipment. Please refer to the safety data sheet before using any of our epoxy products.

5kgs per bottle; 20kgs per carton
20kgs per barrel
200kgs per barrel